济南诚耐金属制品有限公司

济南诚耐金属制品有限公司

不断发展技术力量、完善的设计服务团队,真诚为您提供的服务

咨询热线
于经理15194166167
15990909037

联系我们

企业名称:济南诚耐金属制品有限公司

联系人:于经理

电话: 15990909037

电话: 15194166167

地址:山东省济南市历城区小清河南路8288号

当前位置:首页 »资讯中心 » 常见问题不锈钢门套厂家分享三种安装方法

不锈钢门套厂家分享三种安装方法

来源:http://www.sddtmt.com/ 浏览:0发表时间:2022-12-26
要用玻璃胶粘贴或者封边,然后撕下白色的保护膜。安装也快捷方便。今天小编为大家总结了一些安装方法,一起来看看吧。
Paste or seal the edge with glass adhesive, and then tear off the white protective film. The installation is also fast and convenient. Today, I summarized some installation methods for you. Let's have a look.
1. 常规安装方法:测量确认不锈钢门的尺寸与安装孔的尺寸相同,然后根据孔的位置放置钢门,然后钻孔,固定后调整。将内门放在门框上并锁上,然后将侧装板固定在墙上。之后,外门框和安装板以同样的方式固定。
1. Conventional installation method: measure and confirm that the size of the stainless steel door is the same as the size of the installation hole, then place the steel door according to the position of the hole, drill, fix and adjust it. Place the inner door on the door frame and lock it, then fix the side mounting plate on the wall. After that, the outer door frame and the mounting plate are fixed in the same way.
2 .水泥填充法:因为不锈钢门框基本是镂空的,如果想要更坚固,可以用水泥填充门框的镂空,但也要注意水泥不能填充太多,否则也会影响门框的开启和使用。注满水泥4小时后,取下垫纸,轻轻打开门扇,用螺丝刀将框孔内的水泥清洗干净,然后盖上安装孔。
2. Cement filling method: because the stainless steel door frame is basically hollow, if you want to be more solid, you can fill the hollow of the door frame with cement, but you should also pay attention not to fill too much cement, otherwise it will also affect the opening and use of the door frame. After 4 hours of cement filling, remove the pad paper, gently open the door leaf, clean the cement in the frame hole with a screwdriver, and then cover the installation hole.
3.安装方法:取下门扇,将门框放入门孔内,用水平尺检查,平放。,内门合页的一侧是参考边,将安装板在门框加固上转动,使其与门框垂直,然后用水泥钉将安装板弯曲固定在墙上。
3. Installation method: take down the door leaf, place the door frame in the access hole, check with a level ruler, and lay it flat. First, one side of the inner door hinge is the reference side. Rotate the mounting plate on the door frame reinforcement to make it vertical to the door frame, and then bend and fix the mounting plate on the wall with cement nails.
以上就是为大家介绍的有关电梯不锈钢门套的详细的介绍,希望对您有所帮助.如果您有什么疑问的话,欢迎联系我们.我们将以的态度,为您提供服务http://www.sddtmt.com
The above is a detailed introduction to the stainless steel door pocket of the elevator. I hope it will be helpful to you. If you have any questions, please contact us. We will provide services for you with our attitude http://www.sddtmt.com