济南诚耐金属制品有限公司

济南诚耐金属制品有限公司

不断发展技术力量、完善的设计服务团队,真诚为您提供的服务

咨询热线
于经理15194166167
15990909037

联系我们

企业名称:济南诚耐金属制品有限公司

联系人:于经理

电话: 15990909037

电话: 15194166167

地址:山东省济南市历城区小清河南路8288号

当前位置:首页 »资讯中心 » 新闻资讯

工地门套翻车点排查

来源:http://www.sddtmt.com/ 浏览:0发表时间:2026-11-18

很多工地电梯口装完才发现问题:胶缝吃满、阴阳角露毛边、门套轻微空鼓。返工不一定因为板材差,往往出在“顺序”和“复尺”上。

Many construction site elevator entrances only discover problems after installation, such as full glue seams, exposed edges on internal and external corners, and slight hollowing of door frames. Rework may not necessarily be due to poor board quality, but often results in "sequence" and "re sizing".

量尺别等贴完砖再动

Don't wait until the bricks are pasted before moving the measuring tape

base64_image

正确动作是倒着排:先测土建毛洞,再定门套方案,然后贴砖。毛洞要测净宽、净高、墙体厚度,上中下各量一遍,取实际偏差值。对角线差超过3毫米,说明洞口本身不方,下料图要标“左窄右宽”,不能照标准图直接切。

The correct action is to arrange it upside down: first measure the gross holes in the civil engineering, then determine the door frame plan, and finally tile it. Mao Dong needs to measure the net width, net height, and wall thickness, taking measurements of the upper, middle, and lower parts, and taking the actual deviation value. If the diagonal difference exceeds 3 millimeters, it indicates that the opening itself is not square. The cutting diagram should be marked as "narrow on the left and wide on the right" and cannot be directly cut according to the standard diagram.

贴砖完成后再复尺一次。以电梯原厂门框中心为基准放线,不按左右墙垛平均分。允许单边压边差1到2厘米,用加宽收边线盖住误差。中心对正,视觉上就正,比硬凑对称更稳。

After tiling is completed, repeat the measurement. Set out the line based on the center of the original elevator door frame, without dividing it evenly according to the left and right wall piers. Allow a unilateral edge pressure difference of 1 to 2 centimeters, and cover the error with a widened edge. Center alignment, visually correct, more stable than hard symmetry.

基层和固定方式

Grassroots and fixed methods

混凝土墙可直接打孔固定;轻钢龙骨或加气块墙,要预埋钢板或专用挂件,不能只靠结构胶。

Concrete walls can be directly drilled and fixed; Light steel keel or aerated block wall should be pre embedded with steel plates or specialized hangers, and cannot rely solely on structural adhesive.

传统木龙骨打底有两个隐患:防火等级难过关,受潮后变形会带歪门套。现在多用防火木塑纤维板做基层,现场拼装,粉尘少,工期也短。

There are two hidden dangers in the traditional wooden keel base: the fire rating is difficult to close, and it may deform and cause crooked door frames when exposed to moisture. Nowadays, fire-resistant wood plastic fiberboard is commonly used as the base layer for on-site assembly, resulting in less dust and shorter construction period.

门套与电梯门扇之间留3到5毫米间隙,避免开关摩擦。底部离地完成面留5毫米伸缩缝,打胶防潮,不贴死地面。拼角优先工厂45度折弯一体成型,现场不焊接、不现切。

Leave a gap of 3 to 5 millimeters between the door frame and the elevator door leaf to avoid friction between the switch. Leave a 5mm expansion joint at the bottom off the finished surface, apply glue to prevent moisture, and do not stick to the ground. Priority factory 45 degree bending and integrated molding for corner splicing, no welding or cutting on site.

验收看五个动作

Check the five actions for acceptance

不用听太多术语,现场做这几步:

Don't listen to too many terms, do these steps on site:

2米靠尺查垂直度,偏差不超2毫米

Check the verticality with a 2-meter ruler, and the deviation should not exceed 2 millimeters

量对角线,误差不超3毫米

Measure the diagonal, with an error not exceeding 3 millimeters

拼缝高低差不超0.3毫米,无错台

The height difference of the joint should not exceed 0.3 millimeters, and there should be no misalignment

手推门套,无松动、无空鼓声

Hand pushed door frame, no looseness, no empty drum sound

保护膜装完24小时再撕,不提前揭

The protective film should be removed 24 hours after installation, and should not be removed in advance

打胶前缝隙要干、要干净。同色中性耐候胶,胶缝连续、无气泡。美纹纸在表干前撕掉,胶边才利落。

Before applying glue, the gaps should be dry and clean. Same color neutral weather resistant adhesive, with continuous adhesive seams and no bubbles. Tear off the decorative paper before it dries, and the adhesive edge will be sharp.

门套不是“到货就装”的配件,它是土建、瓷砖、电梯三方尺寸的收口系统。把偏差提前消化在图纸里,现场只做拼装,返工概率会降一大截。

Door frames are not accessories that can be installed immediately upon arrival. They are a three dimensional closure system for civil engineering, ceramic tiles, and elevators. By incorporating deviations into the drawings in advance and only assembling them on site, the probability of rework will be significantly reduced.

本文由工地电梯门套上门安装厂家友情奉献。更多有关的知识请点击:http://www.sddtmt.com我们将会对您提出的疑问进行详细的解答,欢迎您登录网站留言.

This article is a friendly contribution from the on-site installation manufacturer of elevator door frames. For more information, please click: http://www.sddtmt.com We will provide detailed answers to your questions. You are welcome to log in to our website and leave a message