济南诚耐金属制品有限公司

济南诚耐金属制品有限公司

不断发展技术力量、完善的设计服务团队,真诚为您提供的服务

咨询热线
于经理15194166167
15990909037

联系我们

企业名称:济南诚耐金属制品有限公司

联系人:于经理

电话: 15990909037

电话: 15194166167

地址:山东省济南市历城区小清河南路8288号

当前位置:首页 »资讯中心 » 新闻资讯

门洞歪4公分,包完却像精装样板间

来源:http://www.sddtmt.com/ 浏览:0发表时间:2026-11-04

老旧小区改造和新盘精装常卡在同一个地方:瓦工退场了,电梯口才量——左右墙垛差3、4公分,上下还带2公分误差。这时候还按“对称标准套”做,只会越补越丑。

The renovation of old residential areas and the decoration of new buildings often get stuck in the same place: the bricklayers have left, and the elevator has a height difference of 3-4 centimeters between the left and right wall piers, with a margin of error of 2 centimeters above and below. At this point, still following the "symmetrical standard set" will only make it more and more ugly.

base64_image

先别急着下单,现场量三遍:

Don't rush to place an order yet, measure three times on site:

门洞宽、高、墙厚各测上中下三点,取出彩差;

Measure the width, height, and wall thickness of the door opening at three points: upper, middle, and lower, and take the range;

瓷砖完成面、电梯门框凸出量分开记,别混算;

Separate the protrusion of ceramic tile finish and elevator door frame, and do not mix them up;

阴角垂直度用激光投线仪,偏差超5mm先让瓦工修,不靠门套硬遮。

Use a laser projector to measure the verticality of the inner corner. If the deviation exceeds 5mm, have the bricklayer repair it first, without relying on the door frame to cover it.

板材和基层分开算账:

Separate accounting for board and base layer:

室内公共区基材选304,首层/地下车库人流大用1.2–1.5mm实厚,卡尺抽检,标1.2发0.8当场退;

Select 304 as the substrate for indoor public areas, with a thickness of 1.2-1.5mm for heavy pedestrian traffic in the first floor/underground garage. Use calipers for random inspection, with a standard of 1.2 and 0.8 for immediate return;

出彩窄边(可视面1–2cm)别贪好看,基层不平会直接露在缝里,先做防火防潮基层板找平;

Extremely narrow edges (visible surface 1-2cm), do not be tempted by aesthetics. Uneven base layers will be directly exposed in the seams. First, make a fireproof and moisture-proof base layer board to level it;

工厂一体折弯优先,阳角不留焊痕;现场45°拼焊再打磨,色差和微缝后期必显。

Factory integrated bending priority, leaving no welding marks on the external corners; On site 45 ° welding and polishing, color difference and micro seam will be noticeable in the later stage.

收口逻辑比宽度重要:

Closing logic is more important than width:

竖料压门头横料,横板比竖板窄1–2mm,层次才立得住;

Vertical material presses the door head horizontally, and the horizontal plate is 1-2mm narrower than the vertical plate in order for the level to stand upright;

门套内边与电梯门扇留3–5mm,不蹭门、不露黑洞;

Leave 3-5mm between the inner edge of the door frame and the elevator door leaf, without rubbing against the door or exposing any black holes;

阴角别拿胶瞎盖,先装顺再打耐候胶,胶缝连续不气泡。

Don't cover the corners with glue blindly. Install them smoothly first and then apply weather resistant glue. The glue seam should be continuous without bubbles.

安装完验四项:对角线差≤2mm、垂直度≤2mm/m、拼缝≤1mm、保护膜揭掉无划伤。

After installation, check four items: diagonal deviation ≤ 2mm, verticality ≤ 2mm/m, joint ≤ 1mm, and no scratches after removing the protective film.

门套不是遮丑条,是门洞的“修正层”。基层量准、板厚真实、折弯到位,歪门洞也能收出直线。

The door frame is not a cover up strip, but a "correction layer" for the door opening. The grassroots measurement is accurate, the board thickness is true, the bending is in place, and even the crooked door opening can be folded into a straight line.