一：准备：勘察现场  人员  工具  准备

　　1： Preparation: Preparation of survey site personnel and tools

　　二：机械部件安装

　　2： Installation of mechanical components

　　1：导轨安装     1） 支架位置确定：  a)最高 最低 0.5米，中间2.5米b)支架在建筑梁上，误差小于300mm2）支架尺寸要求： 水平误差小于5mm（横。纵）3）导轨尺寸：     a）垂直误差 单根全长小于1mm 每0.7/5000连续三段三次b）相对误差 轿箱侧+2~~0mm   对重侧+3~~0mmc）台阶与间隙：台阶（小于0.05mm）间隙（小于0.5mm）d）对角误差： 小于等于3mm（中心误差） 左右小于1mm   前后小于正负2mm

　　1: Installation of guide rail 1) Determination of bracket position: a) Maximum and minimum 0.5 meters, middle 2.5 meters b) Bracket on building beam, error less than 300mm2) Bracket size requirement: horizontal error less than 5mm (horizontal). Vertical) 3) Guide rail dimensions: a) Vertical error, single length less than 1mm, continuous three sections every 0.7/5000, three times. b) Relative error, car side+2~~0mm, counterweight side+3~~0mmc. Steps and gaps: Steps (less than 0.05mm) Gap (less than 0.5mm). d) Diagonal error: less than or equal to 3mm (center error), left and right less than 1mm, front and rear less than plus or minus 2mm

　　2：曳引机安装  1)曳引机基础高度确定 : 1/2导向轮直径+导向轮最低离地大于150mm2)  钢梁安装：       a）2/1000 水平误差b）平行误差 小于6mmc）焊接厚度 大于6mmd）底板厚度 大于12mm               3）曳引机安装：a）吊装：严格按照超作要求进行超作b）尺寸要求：曳引机垂直误差 小于2mm(有避震)小于1mm(无避震)  c） 制动器： 间隙 小于0.7mm   贴合面：大于80%

　　2: Traction machine installation 1) Determination of traction machine foundation height: 1/2 guide wheel diameter+minimum ground clearance of guide wheel greater than 150mm2) Steel beam installation: a) 2/1000 horizontal error b) Parallel error less than 6mmc) Welding thickness greater than 6mmd) Bottom plate thickness greater than 12mm 3) Traction machine installation: a) Lifting: Strictly follow the overtime requirements b) Size requirements: Traction machine vertical error less than 2mm (with suspension) less than 1mm (without suspension) c) Brake: Gap less than 0.7mm Fitting surface: greater than 80%

　　3：对重安装：对重重量确定 自重+（0.4~~0.5）载重， 对重块必须可靠固定.

　　3: Counterweight installation: The counterweight weight is determined by its own weight plus (0.4~~0.5) load capacity, and the counterweight block must be reliably fixed

　　4：曳引钢丝绳：a）长度确定 ：采用实测方式b） 绳头要求 ：1）截取长度 大于100mm   2）浇筑巴氏合金符合要求c）悬挂必须调整螺杆锥套长度 小于70mm

　　4: Traction wire rope: a) Length determination: measured method used b) Rope head requirements: 1) Cut length greater than 100mm 2) Pouring Babbitt alloy meets requirements c) Suspension must be adjusted with screw cone sleeve length less than 70mm

　　5：轿箱安装 ：  1）轿箱安装尺寸：水平小于1/1000   前后小于1/10002）导靴与导轨间隙： 左右共小于2mm3）安全钳间隙调整 2~~3mm4）轿底水平度 1/1000（横，纵）5）地坎水平度 1/10006）轿壁垂直度 1/1000（装簧板，操纵板处）7）轿门与装饰板间隙 客梯：小于6mm 货梯：小于8mm8）安全触板必须产生中心偏差为10mm9）悬挂门的偏心轮与门导轨间隙 小于0.5mm10）门锁下端离地坎表面 客梯:<6mm   货梯：<8mm11）门中心偏差：小于5mm

　　5: Car installation: 1) Car installation dimensions: horizontal less than 1/1000, front and rear less than 1/10002) Clearance between guide shoes and guide rails: less than 2mm3 on both sides) Clearance adjustment of safety clamps 2~3mm 4) Levelness of car bottom 1/1000 (horizontal and vertical) 5) Levelness of sill 1/10006) Verticality of car wall 1/1000 (at the spring plate and control plate) 7) Clearance between car door and decorative plate Passenger elevator: less than 6mm Freight elevator: less than 8mm 8) The center deviation of the safety contact plate must be 10mm 9) The eccentric wheel of the suspended door and the door guide rail clearance must be less than 0.5mm 10) The lower end of the door lock is less than the surface of the sill Passenger elevator:<6mm Freight elevator:<8mm 11) Door center deviation: less than 5mm

　　6：层门安装：   1）门扇下端      客梯：小于6mm   货梯：小于8mm2）门扇与门套   客梯：小于6mm   货梯：小于 8mm3）地坎水平误差   1/10004）厅门地坎与轿门地坎相对间隙 25~~30mm厅门地坎与轿门地坎相对误差 小于正负1mm5）门锁啮合深度大于7mm6）门球与轿箱地坎间隙    5~~10mm门刀与厅门地坎间隙    5~~10mm

　　6: Installation of landing doors: 1) Passenger elevator at the bottom of the door leaf: less than 6mm; Freight elevator: less than 8mm2; Passenger elevator between the door leaf and the door frame: less than 6mm; Freight elevator: less than 8mm3; Horizontal error of the sill: 1/10004) Relative gap between the hall door sill and the car door sill: 25~30mm; Relative error between the hall door sill and the car door sill: less than plus or minus 1mm; 5) Door lock engagement depth greater than 7mm; 6) Gap between the door ball and the car door sill: 5~10mm; Gap between the door blade and the hall door sill: 5~10mm

　　7：地坎安装：   1）缓冲器垂直误差   0.5/10002）相对高度       小于2mm3）相对中心       小于 20mm4）缓冲器开关必须有效

　　7: Installation of the embankment: 1) Vertical error of the buffer is 0.5/10002) Relative height is less than 2mm3) Relative center is less than 20mm 4) Buffer switch must be effective

　　8：限速器：      1）机房限速轮垂直误差 ： 小于0.5mm2）限速绳与导轨侧面误差：小于20mm3）地坑涨紧装置离地必须符合要求

　　8: Speed limiter: 1) Vertical error of speed limiting wheel in the machine room: less than 0.5mm2) Error between speed limiting rope and guide rail side: less than 20mm3) The ground lifting device of the pit must meet the requirements

　　9：电器装置：   1）控制屏尺寸要求：0.5米（左右）X 0.6米（后侧）X 0.8米（前面）2）电缆在机房必须进入线槽并有可靠接地3）井道电缆不应有扭曲   电缆最低离地大于100mm4）井道线槽必须有可靠接地5）井道照明   0.5米（上下各离最高低端） 7米（灯与灯的距离）6）各类急停   必须有效

　　9: Electrical device: 1) Control screen size requirements: 0.5 meters (left and right) X 0.6 meters (rear) X 0.8 meters (front)

　　10：各种实验： 1）慢速单层   2）慢速多层   3）快速单层   4）快速多层 5）平衡系数 6）制停实验7）提升实验   8）静载实验 电梯在最底层，150%载重，历时10分钟

　　10: Various experiments: 1) Slow single-layer, 2) Slow multi-layer, 3) Fast single-layer, 4) Fast multi-layer, 5) Balance coefficient, 6) Stopping experiment, 7) Lifting experiment, 8) Static load experiment. The elevator is at the bottom layer with a load of 150% and lasts for 10 minutes

　　本文由  济宁电梯门套加工定制  友情奉献.更多有关的知识请点击  http://www.sddtmt.com/   真诚的态度.为您提供为全面的服务.更多有关的知识我们将会陆续向大家奉献.敬请期待.

　　This article is a friendly contribution from Jining Elevator Door Frame Processing Customization For more related knowledge, please click http://www.sddtmt.com/ Sincere attitude To provide you with comprehensive services We will gradually contribute more relevant knowledge to everyone Coming soon.