1、材料厚度必需1.2厚（实际厚度不得小于1.08）。安徽电梯套

1. The material thickness must be 1.2 (actual thickness must not be less than 1.08). Anhui Elevator Set

2、必需注意用竖料来收口门头横料。

2. It is necessary to pay attention to using vertical material to close the horizontal material of the door head.

3、注意制作基层一定要小于门套包边尺寸5mm左右，**足够的空间安装和打胶。

3. Note that the base layer must be about 5mm smaller than the edge size of the door frame, with sufficient space for installation and gluing.

4、门头板宽度要略小于竖料宽度1-2毫米，收口才美观。

4. The width of the door panel should be slightly smaller than the width of the vertical material by 1-2 millimeters for a beautiful closure.

5、一般门头板和立面包板对接处的阴角处不建议用胶水收口，这样既美观又能检验门套安装质量。

5. It is not recommended to use glue to close the inner corners of the junction between the door panel and the facade panel, as this is both aesthetically pleasing and can verify the quality of the door frame installation.

b：普通的45°拼接门套做法，常规注意事项如下：

b: The common 45 ° splicing door frame method requires the following precautions:

1、材料厚度必需1.2厚（实际厚度不得小于1.08）。注意对角处不能有错位，焊接点一定要处理在隐蔽位置。

1. The material thickness must be 1.2 (actual thickness must not be less than 1.08). Be careful not to have any misalignment at the diagonal, and the welding points must be handled in concealed positions.

2、注意制作基层一定要小于门套包边尺寸5mm左右，足够的空间安装和打胶。

2. Note that the base layer must be about 5mm smaller than the edge size of the door frame, with sufficient space for installation and gluing.

3、一般门头板和立面包板对接处的阴角处不建议用胶水收口，这样既美观又能检验门套安装质量。

3. It is not recommended to use glue to close the inner corners of the junction between the door panel and the facade panel, as this is both aesthetically pleasing and can verify the quality of the door frame installation.

安装质量粗劣，阴角打胶遮盖瑕疵，不建议使用

Poor installation quality, with defects covered by glue on the inner corners, not recommended for use

c：常规止口门套做法如左下图，这类做法的弊端：

c: The conventional method of using a stop mouth door frame is shown in the bottom left figure. The drawbacks of this method are:

1、基层不准确时很难卡上去；尺寸不可调节，对于门洞基层有变化时无法改动门套尺寸。

1. It is difficult to get stuck when the grassroots is inaccurate; The size cannot be adjusted, and the door frame size cannot be changed when there are changes in the base layer of the door opening.

2、加工复杂，尺寸较大时运输会有变形风险。

2. When processing is complex and the size is large, there is a risk of deformation during transportation.

建议使用右上图做法，这类做法的有点：

It is recommended to use the method shown in the upper right image, which has some advantages:

基层不准确时可以有效的通过结构分解来化解掉；门套宽度可以小范围调节，能够适应工地现场的变化。尺寸分解后也降低了加工难度和变形风险

When the grassroots is inaccurate, it can be effectively resolved through structural decomposition; The width of the door frame can be adjusted within a small range to adapt to changes on the construction site. The size decomposition also reduces the difficulty of processing and the risk of deformation

需要注意的是推荐做法要注意不锈钢电梯门套安装时两块板保持水平，注意第二块扣板的基层必需准确。

It should be noted that the recommended practice is to keep the two plates level when installing the stainless steel elevator door frame, and to ensure that the base of the second buckle plate is accurate.

以上门套为整体成型，也就是常规的做法，基层不标准造成了拼角出现错位、闪缝等质量问题。影响美观，建议止口板和包板分开，可以有效避免因基层问题而造成的安装瑕疵。

The above door frames are formed as a whole, which is a common practice. The non-standard base layer has caused quality problems such as misalignment and flash joints in the joints. It affects the appearance. It is recommended to separate the sealing plate and the wrapping plate to effectively avoid installation defects caused by grassroots issues.

d：电梯门套常规做法有一部分被挡住属于不可见面积的优化

d: The conventional practice of elevator door frames is to partially block and optimize the invisible area

常规注意事项如下：

The general precautions are as follows:

1、材料厚度必需1.5厚（实际厚度不得小于1.38）。

1. The material thickness must be 1.5 (actual thickness must not be less than 1.38).

2、门头板宽度.好小于里面包板的宽度，这样收口会美观。

2. Width of the door panel It should be smaller than the width of the inner packaging board, so that the closure will look beautiful.

3、注意制作基层一定要小于门套包边尺寸5mm左右，足够的空间安装和打胶。

3. Note that the base layer must be about 5mm smaller than the edge size of the door frame, with sufficient space for installation and gluing.

4、一般门头板和立面包板对接处的阴角处不建议用胶水收口，这样既美观又能检验门套安装质量。

4. It is not recommended to use glue to close the inner corners of the junction between the door panel and the facade panel, as this is both aesthetically pleasing and can verify the quality of the door frame installation.

5、有的门套立面包板上面有一部分被挡住属于不可见面积，但是决算

5. Some door frames have a part of the facade panel that is blocked and belongs to the invisible area, but the final settlement

以上节点可以有效解决我们常规门套生产中的不可见面积的浪费现象。同时边缘卡线富于变化。

The above nodes can effectively solve the waste of invisible area in our conventional door frame production. At the same time, the edge card lines are rich in variation.

门套侧板为整块板决算时造成不可见面积的分歧，但如果采用结构分解为2部分的做法，电梯厅门套使用的是分段处理形成了一条明显拼接缝隙，可以有效解决这个问题。

When the side panel of the door frame is calculated as a whole, it causes a discrepancy in the invisible area. However, if the structure is decomposed into two parts, the elevator hall door frame is segmented to form a clear joint gap, which can effectively solve this problem.

本文由淄博电梯门套厂家为您提供技术支持，更多精彩内容请点击我们的网站：http://www.sddtmt.com

This article is provided with technical support by Zibo Elevator Door Frame Manufacturer. For more exciting content, please click on our website: http://www.sddtmt.com