越是细节

　　The more details

　　越能证明项目的精致与否越是细节

　　The more it proves the delicacy of the project, the more detailed it is

　　越容易被人们忽略用了几个月的时间走完了装修的99步

　　The easier it is for people to overlook, the more months it took to complete the 99 steps of renovation

　　最后的1步难道要折在门套上面吗

　　Do we have to fold the last step on top of the door frame

　　门套虽然看着不起眼

　　Although the door frame looks unremarkable

　　但确是一套门的重要组成部分可不能随便弄弄以了事

　　But it is indeed an important component of a set of doors that cannot be easily tampered with

　　门套

　　door frame

　　不做背锅侠

　　Don't be a scapegoat

　　01为什么要装门套？

　　Why install door frames?

　　①过渡收口很多空间的墙面处理方式是不一样的，这就造成门洞处的收口不雅观，选择用门套，则可以过渡收口，隐藏不好看的一面。还有一些门洞两面采用不一样的油漆颜色，用门套也可以起到过渡作用！

　　① Transition closure: The wall treatment methods of many spaces are different, which results in unsightly closure at door openings. Choosing to use door frames can achieve transition closure and hide the unsightly side. There are also some door openings with different paint colors on both sides, and using door frames can also serve as a transition!

　　②防止碰墙在新办公室进场之前，是少不了家具搬运的 ，搬运的过程难免会磕碰到门洞处的墙体。墙面是瓷砖或乳胶漆，很有可能会磕伤或磕坏；安装门套则可以保护墙体。

　　② Preventing collision with walls is essential before entering the new office. Furniture moving is necessary, and it is inevitable that the wall at the door opening will be bumped during the moving process. The wall is made of ceramic tiles or latex paint, which may cause scratches or damages; Installing door frames can protect the wall.

　　③与门楣结合空间显高当然，门套也不只有一种样式，门套+门楣，装饰效果很好，可以起到显高的作用，非常适合挑高受限的设计选择。

　　③ Combined with the lintel, the space appears taller. Of course, there is not only one style for door frames. The combination of door frames and lintels has a great decorative effect and can enhance the height, making it very suitable for design choices with limited height.

　　④提升颜值门套同样可以作为空间的装饰品，提升整体办公颜值。

　　④ Improving the appearance of the door frame can also serve as a decoration for the space, enhancing the overall office appearance.

　　02不锈钢门套安装工艺及节点

　　02 Stainless steel door frame installation process and nodes

　　①直接对接门套

　　① Directly connect to the door frame

　　◎以上是最普通的直拼对接门套做法，常规注意事项如下：

　　The above is the most common method of directly connecting door frames, and the general precautions are as follows:

　　1）材料厚度建议用1.2厚（实际厚度不得小于1.08）。2）必须注意用竖料来收口门头横料。3）注意制作基层一定要小于门套包边尺寸5mm左右，保证足够的空间安装和打胶。4）门头板宽度要略小于竖料宽度1-2毫米，收口才美观。5）一般门头板和立面包板对接处的阴角处不建议用胶水收口，这样既美观又能检验门套安装质量。

　　1) The recommended material thickness is 1.2 (actual thickness should not be less than 1.08). 2) Attention must be paid to using vertical materials to close the horizontal materials of the door. 3) Note that the base layer must be about 5mm smaller than the edge size of the door frame to ensure sufficient space for installation and gluing. 4) The width of the door panel should be slightly smaller than the width of the vertical material by 1-2 millimeters for a beautiful closure. 5) It is not recommended to use glue to close the inner corners of the junction between the door panel and the facade panel, as this is both aesthetically pleasing and can verify the quality of the door frame installation.

　　②45°拼接门套

　　② 45 ° splicing door frame

　　◎以上是最普通的45°拼接门套做法，常规注意事项如下：

　　The above is the most common 45 ° splicing door frame method, and the general precautions are as follows:

　　1）材料厚度建议1.2厚（实际厚度不得小于1.08）。2）注意对角处不能有错位，焊接点一定要处理在隐蔽位置。3）注意制作基层一定要小于门套包边尺寸5mm左右，保证足够的空间安装和打胶。4）一般门头板和立面包板对接处的阴角处不建议用胶水收口，这样既美观又能检验门套安装质量。

　　1) The recommended material thickness is 1.2 (actual thickness should not be less than 1.08). 2) Be careful not to have any misalignment at the diagonal, and the welding points must be handled in concealed positions. 3) Note that the base layer must be about 5mm smaller than the edge size of the door frame to ensure sufficient space for installation and gluing. 4) It is not recommended to use glue to close the inner corners of the junction between the door panel and the facade panel, as this is both aesthetically pleasing and can verify the quality of the door frame installation.

　　③常规做法

　　③ Conventional practice

　　◎常规止口门套做法如上图，这类做法的弊端：1）基层不准确时很难卡上去；2）尺寸不可调节，对于门洞基层有变化时无法改动门套尺寸。3）加工复杂，尺寸较大时运输会有变形风险。

　　The conventional method of using a stop door frame is shown in the picture above. The drawbacks of this method are: 1) it is difficult to get it stuck when the base layer is inaccurate; 2) The size cannot be adjusted, and the door frame size cannot be changed when there are changes in the base layer of the door opening. 3) When processing is complex and the size is large, there is a risk of deformation during transportation.

　　④推荐做法

　　④ Recommended practice

　　◎常规止口门套做法如上图，这类做法的弊端：1）基层不准确时可以有效的通过结构分解来化解掉。2）门套宽度可以小范围调节，能够适应工地现场的变化。3）尺寸分解后降低了加工难度和变形风险。▲注意安装时两块板保持水平，注意第二块扣板的基层必须准确。

　　The conventional method of using a stop door frame is shown in the figure above. The drawbacks of this method are: 1) When the base level is inaccurate, it can be effectively resolved through structural decomposition. 2) The width of the door frame can be adjusted within a small range to adapt to changes on the construction site. 3) After size decomposition, the processing difficulty and deformation risk have been reduced. ▲ Pay attention to keeping the two plates level during installation, and ensure that the base layer of the second buckle plate is accurate.

　　⑤电梯门套

　　⑤ Elevator door frame

　　◎常规注意事项如下：1）材料厚度建议1.5厚（实际厚度不得小于1.38）。2）门头板宽度最好小于里面包板的宽度，这样收口会美观。3）注意制作基层一定要小于门套包边尺寸5mm左右，保证足够的空间安装和打胶。4）一般门头板和立面包板对接处的阴角处不建议用胶水收口，这样既美观又能检验门套安装质量。

　　The general precautions are as follows: 1) The recommended material thickness is 1.5 (the actual thickness should not be less than 1.38). 2) It is best for the width of the door panel to be smaller than the width of the inner cladding, so that the closure will be aesthetically pleasing. 3) Note that the base layer must be about 5mm smaller than the edge size of the door frame to ensure sufficient space for installation and gluing. 4) It is not recommended to use glue to close the inner corners of the junction between the door panel and the facade panel, as this is both aesthetically pleasing and can verify the quality of the door frame installation.

　　⑥电梯门套

　　⑥ Elevator door frame

　　门套立面包板上面有一部分被挡住属于不可见面积，但是决算时要包含在内，造成了材料的浪费。

　　A part of the facade panel of the door frame is blocked and belongs to the invisible area, but it needs to be included in the final settlement, resulting in material waste.

　　建议在结构上进行优化，如下图所示：

　　Suggest optimizing the structure, as shown in the following figure:

　　以上节点可以有效解决我们常规门套生产中的不可见面积的浪费现象。同时边缘卡线可以有多种变化，机构上既美观又能保持统一整体。

　　The above nodes can effectively solve the waste of invisible area in our conventional door frame production. At the same time, the edge card line can have various changes, which are both aesthetically pleasing and maintain a unified overall structure.

　　本文由 滨州不锈钢电梯门套   友情奉献.更多有关的知识请点击  http://www.sddtmt.com/   真诚的态度.为您提供为全面的服务.更多有关的知识我们将会陆续向大家奉献.敬请期待.

　　This article is a friendly contribution from Binzhou Stainless Steel Elevator Door Frame For more related knowledge, please click http://www.sddtmt.com/ Sincere attitude To provide you with comprehensive services We will gradually contribute more relevant knowledge to everyone Coming soon.