门洞量完再定框,别让电梯口变成返工现场
聊城不少小区旧改和新建单元楼,瓷砖贴完才排电梯门。这时候如果按“标准门洞”直接下料,十有六七要对不上——左右墙垛差两三公分、地坪还没找平,硬装上去不是门扇蹭地坎,就是关门留缝漏光。
Many residential areas in Liaocheng, including old and new unit buildings, only install elevator doors after tiling. If the material is cut directly according to the "standard door opening" at this time, there will be six or seven out of ten discrepancies - the difference between the left and right wall stacks is two or three centimeters, the floor has not been leveled, and if it is installed hard, either the door leaf rubs against the floor sill or the door leaves a gap and leaks light.

铝合金电梯门胜在轻、耐腐蚀、颜色能跟轿厢装潢统一,但它是“跟着土建走”的部件,不是到货拧螺丝就行。现场先把三件事核实清楚:
Aluminum alloy elevator doors excel in being lightweight, corrosion-resistant, and able to match the color of the car decoration, but they are components that follow the construction process and cannot be simply screwed upon arrival. First, verify three things on site:
门洞净尺寸:宽、高、墙厚各量上中下三处,取出彩值;旧梯改造还要核对原厂土建图,非标洞提前让厂家折弯补强。
Net dimensions of the door opening: measure the width, height, and wall thickness at three points: upper, middle, and lower, and take the extreme value; The renovation of old elevators also requires checking the original factory's civil engineering drawings, and non-standard holes should be bent and reinforced by the manufacturer in advance.
型材别用家装料:层门和门框建议6063-T5起步,受力件可用6061-T6;面板厚度按现行更新要求,新件≥1.5mm,保留旧门板也别低于1.2mm。
Do not use household materials for profiles: It is recommended to start with 6063-T5 for layer doors and door frames, and 6061-T6 for load-bearing parts. The panel thickness should follow the current updated requirements, with new parts ≥ 1.5mm and old door panels retained not less than 1.2mm.
基层先找平:铝合金比不锈钢软,墙面平整度误差压到3mm以内再固定,不然应力集中,半年就翘边。
Leveling at the grassroots level: Aluminum alloy is softer than stainless steel, and the wall flatness should be adjusted to within 3mm before fixing. Otherwise, stress concentration may occur, and the edges may curl after six months.
安装时盯两个数据就够了:门框垂直度偏差≤2mm/全高,门扇与地坎间隙1–6mm,关门后用手电照不透光就算合格。 地坎高出装修面2–5mm,防止拖把水倒灌井道;门机皮带张力和光幕灵敏度交给有电梯作业资质的师傅调,别让装修工代劳。
During installation, it is sufficient to focus on two data points: the vertical deviation of the door frame should be ≤ 2mm/full height, the gap between the door leaf and the sill should be 1-6mm, and after closing the door, if it is not transparent when illuminated with a flashlight, it is considered qualified. The height of the trench above the decoration surface should be 2-5mm to prevent mop water from flowing back into the well; Leave the tension of the door machine belt and the sensitivity of the light curtain to qualified elevator operators for adjustment, and do not let the decorator do it on their behalf.
采购合同里把“含现场复尺、含防火基层板、含三年门锁触点维保”写进去,比单纯比单价更省心。
Including "on-site re measurement, fire-resistant base board, and three-year door lock contact maintenance" in the procurement contract is more convenient than simply comparing the unit price.
本文由聊城铝合金电梯门友情奉献.更多有关的知识请点击:http://www.sddtmt.com我们将会对您提出的疑问进行详细的解答,欢迎你登录网站留言.
This article is a friendly contribution from Liaocheng aluminum alloy elevator doors For more information, please click: http://www.sddtmt.com We will provide detailed answers to your questions. You are welcome to log in to our website and leave a message






